verytore.blogg.se - Pencil sharpener blade

Pencil sharpener blade how to#

Then turn counterclockwise to raise the blade.

It’s important to check the blade right away–if it’s dull, you can easily replace it now rather than later! To raise the blade, take a Phillips head screwdriver and put it into one of the holes in the side of your sharpener. Unscrew these, and the entire assembly will come out. The first thing you’ll need to do is locate the two small screws that hold the sharpening assembly in place. Now you’ll see the inner workings of your X Acto pencil sharpener. It usually slides right off, but if it’s stuck, give it a little pull! You can easily pry any remaining clips away with a screwdriver. The first thing you’ll need to do is remove the outer cover from your X Acto pencil sharpener.

Pencil sharpener blade how to#

Steps To Follow: How to Fix X Acto Pencil Sharpener Step 1. Just follow along, and we’ll show you what you need to do to get that perfect point on your favorite writing utensil again. This is why it’s so important to have the right tools and know-how! With this blog post, you’ll learn how to fix X Acto pencil sharpener with these simple steps. I can easily buy a new one when the one I own becomes dull and useless.Sharpening an X Acto pencil can be a tedious task for any office. And at first, I wondered if it’s worth all the trouble. It takes a lot of steps to sharpen a pencil sharpener blade. Screw it in place with a screwdriver (clockwise rotation). Make sure that the sharp edge is on the right side. Use a tweezer to place the blade in its position. Now that the blade is sharp and clean, it’s time to reassemble the sharpener. The metal will rust and corrode and essentially become useless. Leaving moisture on a piece of metal is a bad idea. Even if this not the case and a sharpening really is in order, cleaning it afterward is a good practice.Īfter rubbing it with alcohol, dry the blades with a clean cloth. If this is the case, try rubbing a bit of rubbing alcohol on its surface. Often, all it takes is to clean the blade of gunks for it to work correctly. A few slides should be enough to sharpen the blade.

Slide the sharp end of the blade across the sharpening stone at a 20-degree angle.

Because sharpener blades are tiny, I suggest using a tweezer or, better yet, a needle-nosed plier to hold the blade.

Since sharpener blades are tiny, I suggest sharpening stones with a finer surface. The coarser it is, the more metal it rubs off in a pass. The higher the grit, the less coarse it is. The grit is the measure of the coarseness of a sharpening stone.

Some sharpening stones have different grits.

Place the sharpening stone on a damp cloth so it won’t move around when the sharpening process begins.

Others find that instead of using water, oil is a better whetstone lubricant.

Some sharpening stones don’t need water, so make sure to follow the instructions from the manufacturer. Sharpener blades are tiny and very challenging to hold while sharpening them. If all those blades need sharpening, repeat the blade-removing process on all of them.Ħ. Some sharpeners have more than one blade. Repeat Steps 1 to 4 if there are more Blades

Make sure to hold the sharpener close to the flat surface to limit its bounce when it falls off.ĥ.

Flip the sharpener upside down to remove the blade.Here are pointers to keep in mind when removing the blades: Don’t try digging out the blade with your fingers it can cut you. Make sure to keep track of the screw so assembling the sharpener will not be a problem.įlip over the sharpener to loosen both the screw and the blade. Keep on turning until the screw is completely removed. Insert the screwdriver into the screw and rotate it counterclockwise.

A paperclip or a flat end of a fork can work. If there’s no screwdriver small enough available, use something small and flat and can fit into the screw. If that’s the case, be prepared to get the appropriate screwdriver.